Construction method of rubber insulation board:

1. Shake the container before using the rubber-plastic insulation board to make the glue uniform. In actual installation, use a small jar of glue to prevent it from volatilizing too fast. If necessary, pour the large jar into the small jar and seal the jar mouth when not in use.

2, rubber insulation board using a short and hard brush, the material at both ends of the bonding surface coated with a thin layer of uniform special glue.

3. The natural drying time of the special glue is 3-10 minutes. The length of time depends on the level of the glue, the temperature and humidity of the atmosphere. Generally, it should be followed: the higher the ambient temperature, the greater the relative humidity, the lower the medium temperature, and the pipe The larger the diameter, the thicker the material should be; the exposure time exceeds 20 minutes.

4. When the rubber-plastic insulation board is used, the glue will dry naturally. The correct dry measuring method is "finger touch method". Touch the gluing surface with your fingers. If your fingers will not stick to the surface of the material and the surface of the material does not feel sticky, the glue can be bonded. During bonding, you only need to align and hold the two surfaces of the sticky interface for a while.

5, usually, every kilogram of rubber and plastic special glue can be applied to two square meters of adhesive surface.

6. When connecting two materials under pressure, you don't have to wait until the glue dries. Using wet bonding method, first place the material at the installation place, coat the glue at the interface of the material, correctly adjust the position of the two materials, and soon it will be firmly bonded according to the position you designed.

Eight advantages of rubber insulation board:

1, green environmental protection: does not contain harmful chlorine fluoride in the atmosphere, in line with the ISO14000 international environmental certification requirements, so in the installation and application will not produce any harmful pollutants to the human body.

2. Low thermal conductivity: Rubber-plastic insulation board is a high quality thermal insulation and energy-saving material. It is a nemesis of cold insulation, heat insulation and anti-condensation. The thermal conductivity is low and stable, and it has an isolation effect on any thermal medium.

3, good fire performance: rubber and plastic materials in line with the national standard GB8624 "building materials combustion performance analysis method" after testing to determine the GB8624B1 grade flame retardant materials.

4. Closed bubble structure: rubber and plastic are closed bubble structure, water in the outside air is difficult to penetrate into the material, has excellent anti-water vapor penetration ability, and the appearance of the cold insulation layer does not need to add a vapor barrier layer. The moisture resistance factor μ value of rubber and plastic is greater than 3500(ISO9346) to form a built-in waterproof vapor layer, which does not affect the overall vapor barrier property even if the product is scratched. Rubber is the insulation layer is moisture-proof layer.

5. The thickness of rubber and plastic used is about 2/3 less than that of other insulation materials. Therefore, the space above the floor ceiling can be saved and the indoor height can be improved.

6, long service life: rubber insulation board has excellent weather resistance, anti-aging, anti-cold, anti-heat, anti-drying, anti-moisture, but also has anti-ultraviolet, ozone resistance, twenty-five years of aging, no deformation, maintenance-free service life and other characteristics.

7, the appearance of high-grade, uniform and beautiful rubber and plastic with high elasticity, smooth surface, soft texture, even if installed in the elbow, tee, valves and other irregular components can remain intact, beautiful, the appearance does not need decoration, even without ceiling can also maintain high-grade.

8, easy to install, fast because the material is soft, and no other auxiliary layer, construction and installation is simple, for the installation of the pipeline, with the progress of the pipeline installation

Rubber insulation board with its strong performance advantages, clean appearance and simple and quick installation method is used in central air conditioning, construction, chemical industry, medicine, textile, metallurgy, shipbuilding, vehicles, electrical appliances and other industries and departments of all kinds of cold and hot medium pipes, containers.

Hubei rubber and plastic insulation board factory-Hubei Ovis is a professional rubber and plastic insulation board, rubber and plastic insulation board, rubber and plastic insulation board, color rubber and plastic board, rubber and plastic insulation pipe, rubber and plastic pipe and other rubber and plastic insulation factory, rubber and plastic pipe advanced technology, factory direct sales, reliable quality, reasonable price, welcome to inquire!